Study on corrosion property of laser surface alloyed Cr-CrB2 layers on stainless steel

ZHANG Mankui; SUN Guifang; ZHANG Wei; LIU Weixiang; WANG Kun

doi:10.7510/jgjs.issn.1001-3806.2014.02.020

Volume 38 Issue 2

Mar. 2014

Article Contents

Turn off MathJax

Article Navigation > LASER TECHNOLOGY > 2014 > 38(2): 240-245

Citation:

Study on corrosion property of laser surface alloyed Cr-CrB2 layers on stainless steel

1.
School of Mechanical Engineering, Jiangsu University, Zhenjiang 212013, China;
2.
Jiangsu Lianguan Science & Technology Development Co. Ltd., Zhangjiagang 215624, China

Corresponding author: SUN Guifang, gfsun82@gmail.com ;
Received Date: 2013-05-09
Accepted Date: 2013-06-04

Abstract

In order to improve the wear and corrosion resistance of SUS 304 stainless steel, an alloyed layer of Cr-CrB2 was fabricated on SUS 304 stainless steel using laser surface alloying. The datum about microstructure, phases and the corrosion property of the alloyed layer were obtained. Dense and homogeneous structure and fine grains were observed in the alloyed layer. A metallurgical bonding interface was formed between the alloyed layer and the substrate. The alloyed layer consists of austenite, martensite, Fe-Cr, chromium carbide and chromium boride. The alloyed layer shows higher corrosion resistance and lower corrosion rate than the substrate. The polarization curve of the alloyed layer has a long activaton-passivation segment. Intergranular corrosion and pitting in the grains and the grain boundaries are observed for substrate, and intergranular corrosion occurs mainly in the boundary. The alloyed layer shows intergranular corrosion in combination with pitting in the grains and grain boundaries. The size of the pitting in the substrate is larger than that in the alloyed layer. The results have a great help on the improvement of the wear and corrosion resistance of SUS 304 stainless steel.
- laser technique,
- corrosion,
- laser surface alloying,
- SUS 304 stainless steel,
- Cr-CrB2

References

[1]	LI P, SUN G F, ZHANG W, et al. The failure and enhancing techniques for blade of high-speed mixing machine[J].Pastics,2011,40(6):61-64 (in Chinese).
[2]	HU X M, ZHANG W. Discussion for the problems in the structure design of plastics mixer[J]. Engineering Plastics Application, 2001, 29(2): 32-35 (in Chinese).
[3]	MAJUMDAR J D, CHANDRA B R, MANNA I. Laser composite surfacing of AISI 304 stainless steel with titanium boride for improved wear resistance[J]. Tribology International, 2007, 40(1): 146-152.
[4]	TIAN Y Sh, CHEN Ch Zh, WANG D Y, et al. Analysis of the growth mechanism of TiC crystal and the mechanical properties of the laser alloyed layer on the surface of pure titanium[J]. Laser Technology, 2005, 29(2): 113-115(in Chinese).
[5]	SUN G F, ZHOU R, LI P, et al. Laser surface alloying of C-B-W-Cr powders on nodular cast iron rolls[J]. Surface and Coatings Technology, 2011, 205(8/9): 2747-2754.
[6]	HAN T, WANG A H, PENG J, et al. Submicron MC-type reinforced coating produced by laser alloying[J]. Laser Technology, 2012, 36(4): 441-444 (in Chinese).
[7]	ANANDAN S, PITYANA S, DUTTA M J. Structure-property-correlation in laser surface alloyed AISI 304 stainless steel with WC+ Ni+NiCr[J]. Materials Science and Engineering,2012,A536(11):159-169.
[8]	NATH S, PITYANA S, DUTTA M J. Laser surface alloying of aluminium with WC+Co+NiCr for improved wear resistance[J]. Surface and Coatings Technology, 2012, 206(15): 3333-3341.
[9]	ZHONG M L, LIU W J, ZHANG H J. Corrosion and wear resistance characteristics of NiCr coating by laser alloying with powder feeding on grey iron liner[J]. Wear, 2006, 260(11/12): 1349-1355.
[10]	HEYDARZADEH S M, EBRAHIMI M, GHASEMI H M, et al. Microstructural study of surface melted and chromium surface alloyed ductile iron[J]. Applied Surface Science, 2012, 258(19): 7348-7353.
[11]	SHAN J G, REN J L, DING J Ch, et al. Microstructure and wear resistance of Cr powder alloying layers on cast iron[J]. Laser Technology, 2004, 28(1): 1-4 (in Chinese).
[12]	JORDAN L R, BETTS A J, DAHM K L, et al. Corrosion and passivation mechanism of chromium diboride coatings on stainless steel[J]. Corrosion Science, 2005, 47(5): 1085-1096.
[13]	KIRYUKHANTSEV-KORNEEV P V, PIERSON J F, PETRZHIK M I, et al. Effect of nitrogen partial pressure on the structure, physical and mechanical properties of CrB2 and Cr-B-N films[J]. Thin Solid Films, 2009, 517(8): 2675-2680.
[14]	LI G, LIU L, HOU J Y, et al. Study on microstructure and performance of laser cladding Ni-Zr-Nb-Al amorphous composite coating[J]. Laser Technology, 2011, 35(2): 185-188 (in Chinese).
[15]	COSTA L, LANSFORD K, RAJPUT D, et al. Unique corrosion and wear resistant identification tags via LISITM laser marking[J]. Surface & Coating Technology, 2009, 203(14): 1984-1990.
[16]	RAJPUT D, LANSFORD K, COSTA L, et al. Molybdenum-on-chromium dual coating on steel[J]. Surface and Coatings Technology, 2009, 203(9): 1281-1287.
[17]	YUE T M, YU J K, MAN H C. The effect of excimer laser surface treatment on pitting corrosion resistance of 316LS stainless steel[J]. Surface and Coatings Technology, 2001, 137(1): 65-71.
[18]	NIU Sh R. The research of electrochemical corossion resistance of stalnless steels[D].Lanzhou:Lanzhou University of Technology, 2010: 31-32 (in Chinese).
[19]	LLEWEUYN D T, HUDD R C. Steels:metallurgy and applications[M]. Oxford,UK: Reed Educational and Professional Publishing Ltd.,1998:321.
[20]	DONG H L.The effect of deformation on microstructure and properties of 304 austenitic stainless steel[D]. Nanjing: Nanjing University of Seienee & Technology, 2010: 28-29 (in Chinese).

Proportional views

通讯作者: 陈斌, bchen63@163.com

1.
沈阳化工大学材料科学与工程学院沈阳 110142

Get Citation

PDF

XML

Article views(4142) PDF downloads(748) Cited by()

Proportional views

Study on corrosion property of laser surface alloyed Cr-CrB2 layers on stainless steel

Corresponding author: SUN Guifang, gfsun82@gmail.com;

1. School of Mechanical Engineering, Jiangsu University, Zhenjiang 212013, China;

2. Jiangsu Lianguan Science & Technology Development Co. Ltd., Zhangjiagang 215624, China

Received Date: 2013-05-09

Accepted Date: 2013-06-04

Available Online: 2014-02-25

Abstract: In order to improve the wear and corrosion resistance of SUS 304 stainless steel, an alloyed layer of Cr-CrB2 was fabricated on SUS 304 stainless steel using laser surface alloying. The datum about microstructure, phases and the corrosion property of the alloyed layer were obtained. Dense and homogeneous structure and fine grains were observed in the alloyed layer. A metallurgical bonding interface was formed between the alloyed layer and the substrate. The alloyed layer consists of austenite, martensite, Fe-Cr, chromium carbide and chromium boride. The alloyed layer shows higher corrosion resistance and lower corrosion rate than the substrate. The polarization curve of the alloyed layer has a long activaton-passivation segment. Intergranular corrosion and pitting in the grains and the grain boundaries are observed for substrate, and intergranular corrosion occurs mainly in the boundary. The alloyed layer shows intergranular corrosion in combination with pitting in the grains and grain boundaries. The size of the pitting in the substrate is larger than that in the alloyed layer. The results have a great help on the improvement of the wear and corrosion resistance of SUS 304 stainless steel.

HTML

Reference (20)

[1]	LI P, SUN G F, ZHANG W, et al. The failure and enhancing techniques for blade of high-speed mixing machine[J].Pastics,2011,40(6):61-64 (in Chinese).
[2]	HU X M, ZHANG W. Discussion for the problems in the structure design of plastics mixer[J]. Engineering Plastics Application, 2001, 29(2): 32-35 (in Chinese).
[3]	MAJUMDAR J D, CHANDRA B R, MANNA I. Laser composite surfacing of AISI 304 stainless steel with titanium boride for improved wear resistance[J]. Tribology International, 2007, 40(1): 146-152.
[4]	TIAN Y Sh, CHEN Ch Zh, WANG D Y, et al. Analysis of the growth mechanism of TiC crystal and the mechanical properties of the laser alloyed layer on the surface of pure titanium[J]. Laser Technology, 2005, 29(2): 113-115(in Chinese).
[5]	SUN G F, ZHOU R, LI P, et al. Laser surface alloying of C-B-W-Cr powders on nodular cast iron rolls[J]. Surface and Coatings Technology, 2011, 205(8/9): 2747-2754.
[6]	HAN T, WANG A H, PENG J, et al. Submicron MC-type reinforced coating produced by laser alloying[J]. Laser Technology, 2012, 36(4): 441-444 (in Chinese).
[7]	ANANDAN S, PITYANA S, DUTTA M J. Structure-property-correlation in laser surface alloyed AISI 304 stainless steel with WC+ Ni+NiCr[J]. Materials Science and Engineering,2012,A536(11):159-169.
[8]	NATH S, PITYANA S, DUTTA M J. Laser surface alloying of aluminium with WC+Co+NiCr for improved wear resistance[J]. Surface and Coatings Technology, 2012, 206(15): 3333-3341.
[9]	ZHONG M L, LIU W J, ZHANG H J. Corrosion and wear resistance characteristics of NiCr coating by laser alloying with powder feeding on grey iron liner[J]. Wear, 2006, 260(11/12): 1349-1355.
[10]	HEYDARZADEH S M, EBRAHIMI M, GHASEMI H M, et al. Microstructural study of surface melted and chromium surface alloyed ductile iron[J]. Applied Surface Science, 2012, 258(19): 7348-7353.
[11]	SHAN J G, REN J L, DING J Ch, et al. Microstructure and wear resistance of Cr powder alloying layers on cast iron[J]. Laser Technology, 2004, 28(1): 1-4 (in Chinese).
[12]	JORDAN L R, BETTS A J, DAHM K L, et al. Corrosion and passivation mechanism of chromium diboride coatings on stainless steel[J]. Corrosion Science, 2005, 47(5): 1085-1096.
[13]	KIRYUKHANTSEV-KORNEEV P V, PIERSON J F, PETRZHIK M I, et al. Effect of nitrogen partial pressure on the structure, physical and mechanical properties of CrB2 and Cr-B-N films[J]. Thin Solid Films, 2009, 517(8): 2675-2680.
[14]	LI G, LIU L, HOU J Y, et al. Study on microstructure and performance of laser cladding Ni-Zr-Nb-Al amorphous composite coating[J]. Laser Technology, 2011, 35(2): 185-188 (in Chinese).
[15]	COSTA L, LANSFORD K, RAJPUT D, et al. Unique corrosion and wear resistant identification tags via LISITM laser marking[J]. Surface & Coating Technology, 2009, 203(14): 1984-1990.
[16]	RAJPUT D, LANSFORD K, COSTA L, et al. Molybdenum-on-chromium dual coating on steel[J]. Surface and Coatings Technology, 2009, 203(9): 1281-1287.
[17]	YUE T M, YU J K, MAN H C. The effect of excimer laser surface treatment on pitting corrosion resistance of 316LS stainless steel[J]. Surface and Coatings Technology, 2001, 137(1): 65-71.
[18]	NIU Sh R. The research of electrochemical corossion resistance of stalnless steels[D].Lanzhou:Lanzhou University of Technology, 2010: 31-32 (in Chinese).
[19]	LLEWEUYN D T, HUDD R C. Steels:metallurgy and applications[M]. Oxford,UK: Reed Educational and Professional Publishing Ltd.,1998:321.
[20]	DONG H L.The effect of deformation on microstructure and properties of 304 austenitic stainless steel[D]. Nanjing: Nanjing University of Seienee & Technology, 2010: 28-29 (in Chinese).

Study on corrosion property of laser surface alloyed Cr-CrB2 layers on stainless steel

Abstract

References

Proportional views

通讯作者: 陈斌, bchen63@163.com

Proportional views