Analysis of relationship between laser drilling parameters and draw resistance based on full factorial experiment

SUN Huaqiang; HUAN Hao; QI Meng; LI Qingjian

doi:10.7510/jgjs.issn.1001-3806.2018.06.012

LASER TECHNOLOGY > 2018 > 42(6): 790-795. > DOI: 10.7510/jgjs.issn.1001-3806.2018.06.012

SUN Huaqiang, HUAN Hao, QI Meng, LI Qingjian. Analysis of relationship between laser drilling parameters and draw resistance based on full factorial experiment[J]. LASER TECHNOLOGY, 2018, 42(6): 790-795. DOI: 10.7510/jgjs.issn.1001-3806.2018.06.012

Citation:

PDF (4534 KB)

Analysis of relationship between laser drilling parameters and draw resistance based on full factorial experiment

Ji'nan Cigarette Factory, China Tabacco Shandong Industrial Co. Ltd., Ji'nan 250104, China

More Information

Received Date: December 11, 2017
Revised Date: March 29, 2018
Published Date: November 24, 2018

Graphical Abstract

Abstract

Abstract

Laser drilling can significantly improve cigarette quality, such as total ventilation rate and draw resistance of cigarettes and satisfy consumers' sensory experience. In order to obtain the best combination of laser drilling parameters, the relationship equation between laser drilling parameters and draw resistance was explored by using full factor experiment method on the premise of the fixed absorption index. The results show that pulse width is more significant than the other two factors (power and offset hole size). When the three factors change one unit at the same time, pulse width contributes the most influence on draw resistance, about 10 times that of power and offset hole size. In order to reduce draw resistance, the three main factors should be as large as possible. The interaction between power and offset hole size is more significant than the interaction among other factors. The study provides statistical basis for quality control of draw resistance, and the method of analyzing problems also provides the reference for other similar experiments.
- laser technique,
- laser drilling,
- full factor experiment,
- draw resistance,
- cigarette making machine

FullText(HTML)

References (21)

References

[1]	WU Zh Y, LI L, LI D L, et al. Correlation analysis between cigarette weight, draw resistance, ventilation rate and sensory evaluation of ciga-rette[J].Chinese Tobacco Science, 2010, 31(2):49-53(in Ch-inese).
[2]	YANG G R, LI Zh R, XU J, et al. Research advance on the techno-logy of risk and tar reducing in cigarettes[J].Yunnan Chemical Technology, 2009, 36(2):44-47(in Chinese).
[3]	WANG L, YOU M, CUI X M, et al. Method for predicting draw resistance and ventilation of cigarette based on linear network model[J].Tobacco Science & Technology, 2017, 50(12):85-89(in Ch-inese). http://en.cnki.com.cn/Article_en/CJFDTotal-YCKJ201712013.htm
[4]	TAO Y F, ZHANG Sh H, LI W J, et al. Application of AHP and GRA-based models to quality evaluation of cigarettes from different production sites[J]. Acta Tabacaria Sinica, 2017, 23(1):13-17(in Chinese). http://www.wanfangdata.com.cn/details/detail.do?_type=perio&id=zgycxb201701007
[5]	HAN Y X, CHEN P F, ZHOU Zh Y, et al. Laser perforating technology of tipping paper[J]. Laser Technology, 2002, 26(5):330-333(in Chinese). http://www.wanfangdata.com.cn/details/detail.do?_type=perio&id=jgjs200205018
[6]	XIE X C. The relationship between ventilation rate and physicochemical indicator of cigarette made by online laser punching[J]. Journal of Zhengzhou University of Light Industry(Natural Science Edition), 2015, 30(s1):52-56(in Chinese). http://www.wanfangdata.com.cn/details/detail.do?_type=perio&id=zzqgyxy201503014
[7]	XIA P Y, WANG J W, PEI H B, et al. Application of mathematical model for ventilation rate of tipping paper in blended cigarette design[J]. Tobacco Science & Technology, 2009, 42(8):10-13(in Ch-inese). http://en.cnki.com.cn/Article_en/CJFDTOTAL-YCKJ200908004.htm
[8]	YU H. Study on measurement of femtosecond laser pulse wide[J]. Laser Technology, 2013, 37(5):679-681(in Chinese). http://en.cnki.com.cn/Article_en/CJFDTOTAL-JGJS201305026.htm
[9]	HE Y J, WANG W, XU B Zh, et al. Experimental study on deep laser drilling by the superposed pulsed lasers[J]. Laser Technology, 2017, 41(3):380-384(in Chinese). http://www.wanfangdata.com.cn/details/detail.do?_type=perio&id=jgjs201703015
[10]	QIAN X Zh, WANG Q Q, REN N F. Optimization of laser drilling processing parameters for SUS304 based on orthogonal experiments[J]. Laser Technology, 2017, 41(4):578-581(in Chinese). http://en.cnki.com.cn/Article_en/CJFDTotal-JGJS201704024.htm
[11]	XU B Zh, QI L J, WANG W, et al. Study on the optimum matching parameters of the combined laser drilling[J]. Laser Technology, 2018, 42(1):5-10(in Chinese). http://www.wanfangdata.com.cn/details/detail.do?_type=perio&id=jgjs201801002
[12]	MA F Sh, ZHOU W, LIU Ch B. Six sigma statistical guide:MINITAB guidance[M]. Beijing:China Renmin University Press, 2013:447-560(in Chinese).
[13]	MA L, HE Zh. Six sigma management[M]. Beijing:China Renmin University Press, 2007:314-365(in Chinese).
[14]	TANG X F. Six sigma core tutorials-black belt reader[M]. Beijing:Standards Press of China, 2006:449-492(in Chinese).
[15]	LI X B, WANG Y H, XU L. Study on the optimization for the extraction of hawthorn flavonoids and the evaluation of smoking quality with its application in cigarettes[J]. The Food Industry, 2016, 37(10):104-108(in Chinese). http://en.cnki.com.cn/Article_en/CJFDTotal-SPGY201610028.htm
[16]	MA L, WANG W. Full factorial DOE optimizes the preparation process of topiramate pellets[J]. Chinese Journal of New Drugs, 2017, 26(19):2347-2351(in Chinese).
[17]	SUN D L, MI Q, HU J J. Study on consistency of cigarette manufacturing quality[J] Tobacco Science & Technology, 2007, 40(4):9-12(in Chinese). http://www.wanfangdata.com.cn/details/detail.do?_type=perio&id=yckj200704002
[18]	WANG L, LIU X J, WANG Q, et al. Fractional factorial design of experiment for wave soldering process of air conditioner motherboard[J]. Electronic Components and Materials, 2014, 33(5):75-79(in Chinese). http://www.wanfangdata.com.cn/details/detail.do?_type=perio&id=dzyjycl201405018
[19]	MIAO Q D. Analyzing on effects of impurity elements on the hardness of titanium sponge by MINITAB software[J]. Light Metals, 2014(1):44-47(in Chinese). http://www.en.cnki.com.cn/Article_en/CJFDTotal-QJSS201401012.htm
[20]	GE X L, FENG X X, FAN Ch Y. Progress of the study of phase discontinuity of laser propagation through atmosphere[J]. Laser Technology, 2012, 36(4):485-489(in Chinese). http://www.wanfangdata.com.cn/details/detail.do?_type=perio&id=jgjs201204013
[21]	SUN Y Q, ZHOU J Zh, LIANG Q L, et al. Optimization of laser peening parameters using Taguchi method[J]. Laser Technology, 2008, 32(4):377-379(in Chinese). http://www.scientific.net/AMM.10-12.692

Cited By

Get Citation

PDF

XML

Article views (4) PDF downloads (5)

Turn off MathJax

Article Contents

Abstract

References

Analysis of relationship between laser drilling parameters and draw resistance based on full factorial experiment

Abstract

References

Catalog

Links：

Analysis of relationship between laser drilling parameters and draw resistance based on full factorial experiment

Abstract

References

Catalog

Links：

Export File

Citation

Format

Content