Experimental optimization of the output performance of a all-solid-state pulsed Nd:YAG laser

LI Bin-cheng

A simple cavity design for a pulsed Nd:YAG laser employed a 1mm-diameter laser rod pumped by a single laser diode module was reported.An experiment was performed to optimize the cavity design to obtain a laser output of 10W average power and a nearly diffraction-limited TEM00 mode.In this design,the small-diameter laser rod was used to eliminate the oscillation of high-order transverse modes,and a combination of a curved rear mirror and a negative lens placed inside the cavity was employed to compensate the thermal lens effect inside the laser rod.By experimentally optimizing the values of curvature of the rear mirror,the focal length of the negative lens,and the cavity spacing to maximize simultaneously the output power and the beam circularity,the pulsed Nd:YAG laser reached an average power of 10.8W,a beam circularity of 98.8%±0.8%,and M2 value of 1.1.The experimental results showed that in laser engineering the small-diameter laser rod could be used to improve the beam quality of high-power lasers.

1. Institute of Optics and Electronics, Chinese Academy of Sciences, Chengdu 610209, China

Received Date: 2006-03-23

Accepted Date: 2006-04-03

Available Online: 2007-04-25

Abstract: A simple cavity design for a pulsed Nd:YAG laser employed a 1mm-diameter laser rod pumped by a single laser diode module was reported.An experiment was performed to optimize the cavity design to obtain a laser output of 10W average power and a nearly diffraction-limited TEM00 mode.In this design,the small-diameter laser rod was used to eliminate the oscillation of high-order transverse modes,and a combination of a curved rear mirror and a negative lens placed inside the cavity was employed to compensate the thermal lens effect inside the laser rod.By experimentally optimizing the values of curvature of the rear mirror,the focal length of the negative lens,and the cavity spacing to maximize simultaneously the output power and the beam circularity,the pulsed Nd:YAG laser reached an average power of 10.8W,a beam circularity of 98.8%±0.8%,and M2 value of 1.1.The experimental results showed that in laser engineering the small-diameter laser rod could be used to improve the beam quality of high-power lasers.

HTML

Reference (9)

[1]	GOWER M C.Industrial application of laser micromachinig[J].Optics Express,2000,7(2):56～67.
[2]	BOOTH H J.Recent applications of pulsed lasers in advanced materials processing[J].Thin Solid Films,2004,453～454:450～457.
[3]	LIU Y Y,FANG G Zh,LIU B et al.Laser diode side-pumped CW Nd:YAG lasers[J].Chinese Journal of Lasers,2003,30(7):577～580(in Chinese).
[4]	ZHAO Zh M,LI L,TIAN F et al.High power end-pumped intracavity frequency doubling Watt-level green laser[J].Laser Technology,2003,27(4):331～333(in Chinese).
[5]	XU D G,YAO J Q,CHEN J et al.High-stabilization 85W all-solidstate green laser operation[J].Chinese Journal of Lasers,2004,31(4):385～389(in Chinese).
[6]	LI L,YANG S H,SUN W F et al.LD-pumped Yb:YAG chip laser with high beam quality[J].Chinese Journal of Lasers,2004,31(11):1285～1288(in Chinese).
[7]	HU Ch H,BI Y,SUN Zh P et al.Laser-diode pumped 500W continuous-wave Nd:YAG laser[J].Chinese Journal of Lasers,2005,32(1):13～15(in Chinese).
[8]	GAO Q S,TONG L X,JIANG J F et al.The four-pass pumped coupling system of the high power diode lasers stack[J].Laser Technology,2005,29(2):135～137(in Chinese).
[9]	KOECHNER W.Solid-state laser engineering[M].Berlin:Springer,1999.195～236,406～441.

Experimental optimization of the output performance of a all-solid-state pulsed Nd:YAG laser

Abstract

References

Proportional views

通讯作者: 陈斌, bchen63@163.com

Proportional views