Colorimetric temperature measurement device based on ignition point test of magnesium alloy
-
1.
National Key Laboratory for Electronic Measurement Technology, North Univeristy of China, Taiyuan 030051, China
-
Corresponding author:
HAO Xiaojian, haoxiaojian2013@126.com
;
-
Received Date:
2013-08-23
Accepted Date:
2013-11-04
-
Abstract
To solve the measurement of ignition point, the key parameter of ignition-proof magnesium alloy, the colorimetric temperature measurement method was used for the theoretical analysis and experimental verification. A colorimetric temperature measurement device with new structure was designed. The time of the ignition of magnesium alloy was determined from the mutation point of optical radiant energy received by the temperature measurement device and then the ignition temperature was obtained. The static calibration coefficients were gotten from the static calibration of the moderate temperature blackbody furnace. Moderate temperature blackbody furnace was utilized to calibrate statically to obtain static calibration coefficient. Magnesium alloy was ignited with an electrical heating slice resistance with the advantages of simple operation, saving time and test materials. The results of the ignition test of AZ80 with Nd (mass fraction of 0.0075) by colorimetric temperature measurement device and infrared thermometer were 1164.7K and 1148.2K, respectively, whose relative error was 1.4%. The results show that this method solves the difficulty of testing the ignition point of magnesium alloy successfully and has very important reference value for the related research of flame retardant magnesium and on-line monitoring of magnesium alloy smelting.
-
-
References
|
[1]
|
WANG R, HAO X J, ZHOU H C, et al.Design of infrared signal detection circuit in a temperature calibration system[J].Laser Technology, 2013,37(2):247-250(in Chinese). |
|
[2]
|
GE M Z, XIANG J Y, ZHANG Y K. Effect of laser shock processing on resistance to stress corrosion cracking of tungsten inert-gas welded AZ31B magnesium alloy [J]. Laser and Optoelectronics Progress, 2012(12):1203007(in Chinese). |
|
[3]
|
TANG H G, GAO M, ZENG X Y. Tensile strength and microstructure of laser welding of AZ31 magnesium alloy thick plates[J]. Laser Technology, 2011, 35(2):152-155(in Chinese). |
|
[4]
|
LIU S H, LIU J L, LIU H, et al. AZ91 magnesium alloy welding based on YAG pulsed laser[J]. Laser Technology, 2010, 34(4): 459-462(in Chinese). |
|
[5]
|
ZHAO H J, ZHANG Y H, KANG Y L. Effect of cerium on the ignition point of AZ91D magnesium alloy[J]. Light Alloy Fabrication Technology, 2008, 36(2):42-57(in Chinese). |
|
[6]
|
ZHANG X Y, LI Q N, ZHANG Q. Research progress of ignition proof magneium alloy with Ca[J]. Hot Working Technology, 2011, 40(16):4-6(in Chinese). |
|
[7]
|
QIN L, DING J, ZHAO W M, et al. Effect of Ce and Ca additions on property and structure of ignition-proof magnesium alloy[J]. Foundry, 2013, 62(5): 388-392(in Chinese). |
|
[8]
|
WANG P, SHINOZAKI K, YAMAMOTO M. Evaluation of solidification cracking susceptibility during laser welding by in-situ observation method[J]. Chinese Journal of Lasers, 2011, 38(6): 0603005(in Chinese). |
|
[9]
|
CHEN P, ZHANG M X. Measurement for the flammability point of Mg and Mg alloy[J]. Special Casting and Nonferrous Alloys, 2001(2):323-326(in Chinese). |
|
[10]
|
BOBRYSHEV B L. Igintion of magnesium and its alloys[J]. Metal Science and Heat Treatment, 1988, 30(3):219-222. |
|
[11]
|
YUAN C M, HUANG D Z, LI C, et al. Ignition behavior of magnesium powder layers on a plate heated at constant temperature[J]. Journal of Hazardous Materials, 2013, 246/247:283-290. |
|
[12]
|
ZHU J H, HAO X J, ZHOU H C. Implementation of the measurement method and system for transient high-temperature based on colorimetric temperature measurement[J]. Automation and Instrumentation, 2010, 25(9): 5-8(in Chinese). |
-
-
Proportional views
-
Map
DownLoad: