大口径动态扫描反射镜背部悬浮支撑结构设计

张翼; 靳国华; 姜勇; 彭涛

doi:10.7510/jgjs.issn.1001-3806.2016.03.030

高级检索

ISSN 1001-3806CN 51-1125/TN 网站地图

留言板

尊敬的读者、作者、审稿人, 关于本刊的投稿、审稿、编辑和出版的任何问题, 您可以本页添加留言。我们将尽快给您答复。谢谢您的支持!

姓名
邮箱
手机号码
标题
留言内容
验证码

大口径动态扫描反射镜背部悬浮支撑结构设计

张翼 , 靳国华 , 姜勇 , 彭涛

文章导航 > 激光技术 > 2016 > 40(3): 441-446

引用本文:

Citation:

大口径动态扫描反射镜背部悬浮支撑结构设计

1.
西南技术物理研究所, 成都 610041

作者简介: 张翼(1971-),男,硕士,高级工程师,主要研究方向为激光技术、机械设计。E-mail:rzy209@163.com.

中图分类号: TN202

Design of back suspension support structures for large scale dynamic scanning mirrors

1.
Southwest Institute of Technical Physics, Chengdu 610041, China
CLC number: TN202

摘要: 为了消除自重和热应力对大口径平面反射镜面形精度的影响,采用有限元分析方法,对比分析了在-20℃环境温度下采用背部固定约束与背部浮动约束获得的反射镜面形仿真数据,设计了动态扫描反射镜背部悬浮支撑结构以实现浮动约束,搭建了检测平台,并进行了大口径平面反射镜面形检测。结果表明,安装该支撑结构后反射镜的面形峰谷值为0.236,平均值为0.049。背部悬浮支撑结构实现了浮动约束,释放了大口径平面反射镜因自重和热应力造成的变形,有效保证了面形精度。
- 光学设计 /
- 悬浮支撑 /
- 仿真分析 /
- 大口径平面反射镜
Abstract: For eliminating the effects of weight and thermal stress on the surface accuracy of a large flat mirror, the surface accuracy was analyzed for the back fixed constraint and the back float constraint structures at -20℃ by means of the finite element method. The design of support structure using finite element method was studied. By using the back fixed constraint and the float constraint at -20℃, the simulation data of mirror surface accuracy was obtained and analyzed comparatively. The back suspension support structure for dynamic scanning mirrors was designed to achieve the back float constraint. After the establishment of detection platform, the profile of the large flat mirror was measured. The results show that the values of peak-to-valley and root mean square of the flat mirror with back suspension support structure were 0.236 and 0.049 respectively. The back suspension support structure could achieve float constraint and release the surface shape deformation of large flat mirrors caused by weight and thermal stress and ensure the surface accuracy effectively.
- optical design /
- suspension support /
- simulation analysis /
- large flat mirror

[1]	YE L, WANG Zh X. Supporting and adjusting for collimator primary mirror with large aperture and long focal-length[J]. Optics and Precision Engineering,2000,8(5):462-465(in Chinese).
[2]	LI F, RUAN P, ZHAO B Ch. Study on the surface deformation of flat reflector under gravity load[J]. Acta Photonica Sinica,2005,34(2):272-275(in Chinese).
[3]	FENG Sh L, ZHANG X, WENG Zh Ch, et al. Study on support way of large aperture mirror with flat rear surface[J].Optical Technique,2004,30(6):679-681(in Chinese).
[4]	DING F J, LI Y C. The stress and strain analysis ofmain reflector with uniform pressure support and support angle optimization[J]. Acta Photonica Sinica,1998,27(11):1041-1045(in Chinese).
[5]	LIU M, HU Q Q. A study on support structure of the one meter primary mirror of the space solar telescope[J]. Astronomical Research and Technology-Publications of National Astronomical Observatories of China,2004,1(2):99-106(in Chinese).
[6]	DING Y W, YOU Zh, LU H, et al. A thermo-optical analysis method for a space optical remote sensor optostructural system[J]. Optical Engineering, 2004,43(11):2730-2735 (in Chinese).
[7]	WU Q W, YANG H B, YANG J S. Design and analysis for primary mirror and its support of spacecamera[J]. Optical Technology, 2004,30(2):153-156 (in Chinese).
[8]	ZHANG W G, FENG Zh X, TAO Zh. Modal analysis and dynamicde for mation of scanning mirror[J]. Journal of Applied Optics,2006,27(1):58-61(in Chinese).
[9]	YANG L W, LI Zh L, XUE D L. Analysis and test for effect of structural adhesive shrinkage during curing on mirror surface[J]. Optical Technique, 2014, 40(4):307-312(in Chinese).
[10]	YODER P R. Opto-mechanical systems design[M].Beijing:China Machine Press,2008:125-127(in Chinese).
[11]	LIU Q, HE X, ZHANG F, et al. Calculation and control of adhesive layer in reflector athermal mount[J]. Optics and Precision Engineering, 2012,20(10):2229-2236.

[1]	周宇翔 , 沈霞 . 空间反射镜背部双脚架柔性支撑结构设计. 激光技术, 2017, 41(1): 141-145. doi: 10.7510/jgjs.issn.1001-3806.2017.01.029
[2]	宋艳 , 马世榜 , 张开飞 . 热弹激光超声激励及缺陷检测的有限元分析. 激光技术, 2021, 45(2): 246-251. doi: 10.7510/jgjs.issn.1001-3806.2021.02.021
[3]	王顺 , 程高峰 , 李强 , 杨建昌 , 闫宗群 . 激光发射天线仿真平台设计. 激光技术, 2019, 43(1): 131-136. doi: 10.7510/jgjs.issn.1001-3806.2019.01.026
[4]	林超 , 沈学举 , 杨胜翔 . 空间光调制器实现随机相位模板的仿真分析. 激光技术, 2013, 37(3): 365-370. doi: 10.7510/jgjs.issn.1001-3806.2013.03.022
[5]	杨立洁 , 邢鹤园 , 王桂梅 , 郭炜 . 紫外荧光法SO₂监测仪激发光光路的设计仿真. 激光技术, 2021, 45(1): 67-72. doi: 10.7510/jgjs.issn.1001-3806.2021.01.012
[6]	谢洪波 , 李勇 , 姚丽娟 , 祝世民 . 激光转镜扫描系统中自由曲面f-物镜的设计. 激光技术, 2014, 38(6): 742-746. doi: 10.7510/jgjs.issn.1001-3806.2014.06.005
[7]	王智用 , 胡友友 , 李波 , 岳建堡 , 李杰雄 . 用于高功率径向偏振光的组合轴锥镜设计. 激光技术, 2017, 41(6): 846-851. doi: 10.7510/jgjs.issn.1001-3806.2017.06.016
[8]	李畅 , 何欣 . 大口径反射镜轻量化及其支撑结构设计. 激光技术, 2015, 39(3): 337-340. doi: 10.7510/jgjs.issn.1001-3806.2015.03.012
[9]	王毅刚 , 刘力双 , 康登魁 , 姜昌录 . 用于深空探测快速反射镜的电磁驱动. 激光技术, 2023, 47(2): 214-219. doi: 10.7510/jgjs.issn.1001-3806.2023.02.009
[10]	范一鸣 , 魏勇 , 张戈 , 李宏民 , 陶家友 , 周岳平 . 基于V型谐振腔的热稳定性分析. 激光技术, 2018, 42(2): 206-211. doi: 10.7510/jgjs.issn.1001-3806.2018.02.013
[11]	梅艳莹 , 杨涛 . 强光辐照下白宝石高反镜尺寸对热变形的影响. 激光技术, 2014, 38(3): 375-379. doi: 10.7510/jgjs.issn.1001-3806.2014.03.020
[12]	李鹏飞 , 朱向冰 , 陈壮壮 . 轻小型头戴显示器的光学设计. 激光技术, 2021, 45(2): 202-207. doi: 10.7510/jgjs.issn.1001-3806.2021.02.013
[13]	于远航 , 王文生 . 折衍混合紫外告警光学系统设计. 激光技术, 2012, 36(3): 421-423,427.
[14]	邵娜 , 朱晓 , 朱广志 , 王牧 , 冯玙璠 , 黄彦 . 碟片激光器晶体模块阵列射流冲击冷却的研究. 激光技术, 2016, 40(5): 695-700. doi: 10.7510/jgjs.issn.1001-3806.2016.05.016
[15]	李成江 . 激光聚光系统中激光光学与几何光学设计参数间的差异研究. 激光技术, 1994, 18(5): 277-280.
[16]	孙浩 , 唐勇 , 李京展 , 贾天祥 , 杨铭 , 张远健 , 柴利飞 , 陈宝莹 . 硬盘盘片表面疵病检测装置的光学系统设计. 激光技术, 2012, 36(1): 118-119,123. doi: 10.3969/j.issn.1001-3806.2012.01.030
[17]	朱海宇 , 马军 , 张鸿佳 , 王文生 . 刑侦日盲紫外折衍混合变焦光学系统设计. 激光技术, 2015, 39(2): 242-246. doi: 10.7510/jgjs.issn.1001-3806.2015.02.021
[18]	王诗昊 , 向阳 , 申屠功伟 . 外鼓式热敏CTP制版机光学系统设计. 激光技术, 2023, 47(1): 98-102. doi: 10.7510/jgjs.issn.1001-3806.2023.01.015
[19]	彭涛 , 陶刚 , 姜勇 , 周鼎富 . 激光测风雷达折射式收发同轴光学天线设计. 激光技术, 2017, 41(5): 684-687. doi: 10.7510/jgjs.issn.1001-3806.2017.05.013
[20]	豆修浔 , 朱佳巍 , 丁桂林 . 手机镜头的光学系统设计及杂散光模拟. 激光技术, 2016, 40(4): 500-505. doi: 10.7510/jgjs.issn.1001-3806.2016.04.010

点击查看大图

计量

文章访问数: 5041
HTML全文浏览量: 2444
PDF下载量: 418
被引次数: 0

大口径动态扫描反射镜背部悬浮支撑结构设计

作者简介: 张翼(1971-),男,硕士,高级工程师,主要研究方向为激光技术、机械设计。E-mail:rzy209@163.com

1. 西南技术物理研究所, 成都 610041

收稿日期: 2015-03-26
录用日期: 2015-05-06
网络出版日期: 2016-05-25

关键词:

摘要: 为了消除自重和热应力对大口径平面反射镜面形精度的影响,采用有限元分析方法,对比分析了在-20℃环境温度下采用背部固定约束与背部浮动约束获得的反射镜面形仿真数据,设计了动态扫描反射镜背部悬浮支撑结构以实现浮动约束,搭建了检测平台,并进行了大口径平面反射镜面形检测。结果表明,安装该支撑结构后反射镜的面形峰谷值为0.236,平均值为0.049。背部悬浮支撑结构实现了浮动约束,释放了大口径平面反射镜因自重和热应力造成的变形,有效保证了面形精度。