中高温条件下激光冲击处理Ti-6Al-4V表面完整性变化

侯丽华; 任旭东; 周王凡; 戴文杰; 徐士东; 黄晶晶

doi:10.7510/jgjs.issn.1001-3806.2016.02.029

中高温条件下激光冲击处理Ti-6Al-4V表面完整性变化

1.
江苏大学机械工程学院, 镇江 212013

作者简介: 侯丽华(1988-),女,硕士研究生,现主要从事机械制造及其自动化专业的研究。.

通讯作者: 任旭东, renxd@mail.ujs.edu.cn ;

基金项目:
国家自然科学基金资助项目(51275556)
中图分类号: TG156.99

Change of surface integrity of Ti-6Al-4V titanium alloy by laser shock processing at middle and high temperatures

1.
School of Mechanical Engineering, Jiangsu University, Zhengjiang 212013, China

Corresponding author: REN Xudong, renxd@mail.ujs.edu.cn ;

CLC number: TG156.99

摘要: 为了研究中高温条件下激光冲击处理对Ti-6Al-4V钛合金的表面完整性的影响,采用高功率、短脉冲Nd:YAG激光器对Ti-6Al-4V钛合金表面进行激光冲击,并将冲击后的钛合金试样分别置于400℃,500℃,550℃和600℃的温度下进行保温处理。从表面形貌、表面粗糙度、表面残余应力等方面分析了中高温条件下激光冲击处理对Ti-6Al-4V钛合金的表面完整性的影响。结果表明,激光冲击处理增大了Ti-6Al-4V钛合金的表面粗糙度,且热处理温度越高,Ti-6Al-4V钛合金的表面粗糙度越大;激光冲击处理显著提高了Ti-6Al-4V钛合金材料的表面残余压应力,随着温度的升高,残余压应力值降低。研究结果对了解和掌握Ti-6Al-4V钛合金的使用性能是有帮助的。
- 激光技术 /
- 表面完整性 /
- 中高温 /
- Ti-6Al-4V钛合金
Abstract: In order to study effect of laser shock processing (LSP) on surface integrity of Ti-6Al-4V titanium alloy at middle and high temperatures, a high power short pulse Nd:YAG laser was used to shock the surface of Ti-6Al-4V titanium alloy. And then, the specimens after LSP were held at 400℃, 500℃, 550℃ and 600℃ respectively for one hour. The influence of LSP on surface integrity of Ti-6Al-4V titanium alloy at middle and high temperatures were analyzed from surface morphology, surface roughness and surface residual stress. The results indicate that LSP increases the surface roughness of Ti-6Al-4V titanium alloy. The surface roughness increases with the increase of heat treatment temperature. The surface residual stress of Ti-6Al-4V titanium alloy increases obviously after LSP. The higher the temperature, the smaller the surface residual stress is. The research results are helpful for understanding the performance of Ti-6Al-4V titanium alloy.
- laser technique /
- surface integrity /
- middle and high temperatures /
- Ti-6Al-4V titanium alloy

[1]	HUANG X, LI Zh X, HUANG H. Recent development of new high-temperature titanium alloys for high thrust-weight ratio aero-engines[J]. Materials China,2011,30(6):20-27(in Chinese).
[2]	BI X G, BU F L, KANG J. Titanium alloy drilling and new development[J]. Tool Engineering,2008,42(12):19-22(in Chinese).
[3]	HACKEL L A, CHEN H L. Laser peening-A processing tool to strengthen metals or alloys to improve fatigue lifetime and retard stress-induced corrosion cracking[M]. Berlin,Germany:Springer-Verlag,2003:1058-1061.
[4]	LI L, SUN J K, MENG X J. Development and application of titanium alloy[J]. Titanium Industry Progress,2004,21(5):19-23(in Chinese).
[5]	MONTROSS C S, TAO W, LIN Y, et al. Laser shock processing and its effects on micro-structure and properties of metal alloys:a review[J]. International Journal of Fatigue, 2002, 24(2):1021-1036.
[6]	ZHANG Y K, CHEN J F, XU R J. Experimental research of laser shock strengthening AM50 magnesium alloy[J]. Chinese Journal of Lasers, 2008, 35(7):1068-1072(in Chinese).
[7]	REN X D, ZHANG T, ZHANG Y K, et al. Improving fatigue properties of 00Cr12 alloy by laser shock processing[J]. Chinese Journal of Lasers,2010, 37(8):2111-2115(in Chinese).
[8]	PEI X, REN A G, GU Y Y, et al. Effects of laser shock processing on mechanical properties of AZ91 magnesium alloy[J]. Laser Technology, 2010, 34(4):552-556(in Chinese). WANG D Sh, TIAN Z J, SHEN L D, et al. Research states of laser surface modification technology on titanium alloys.Laser Optoelectronics Progress,2008,45(6):24-32(in Chinese). SUN Z C, SUN H L, HUANG Z W, et al. Research progress on surface oridation resistant modification technology of tanium alloy.Materials Review,2011,5(17):507-509(in Chinese).
[9]	YU K G, XIANG B L, QING X Y. Influence of surface integrity on fatigue strength of 40CrNi2Si2MoVA steel[J].Material Letters, 2007, 61(1/2):466-469.
[10]	HUANG Sh, ZHOU J Zh, SUN Y Q, et al. Study on surface integrity of 6061-T6 aluminum alloy sheet after laser shot peening[J]. Applied Laser,2007,27(6):450-455(in Chinese).
[11]	LIU X L, AN Zh X, DING Zh M, et al. Effect of high temperature oxidation treatment on the surface morphology and properties of valve steel[J]. Locomotive Rolling Stock Technology, 2007,18(1):8-12(in Chinese).
[12]	GUO B G, LIANG J, CHEN J M, et al. Effects of oxidation time on micro-structure and performance of micro-arc oxidation coatings formed on Ti-6Al-4V alloy[J]. Chinese Journal of Nonferrous Metals, 2005, 15(6):982-984(in Chinese).
[13]	REN X D, RUAN L, HUANG F Y, et al. Experimental research of laser shock processing 6061-T651 aluminum alloy during elevated temperature[J]. Chinese Journal of Lasers,2012, 39(3):1231-1234(in Chinese).
[14]	ELIEZER S, RAICHER N N E, MARTINEZ-VAL J M. Relativistic shock waves induced by ultra-high laser pressure[J]. Laser and Particle Beams, 2014, 32(2):243-251.
[15]	LU Ch L, HU F Y, HUANG X R, et al. Numerical simulation of temperature and stress field of metal plates irradiated by pulsed laser[J]. Laser Technology, 2012,36(6):754-758(in Chinese).
[16]	JUIJERM P, ALTENBERGER I. Residual stress relaxation of deep-rolled Al-Mg-Si-Cu alloy during cyclic loading at elevated temperatures[J]. Scripta Materialia, 2006,55(12):1111-1114.
[17]	WANG X F, PAN A X. Experimental study of residual stress with laser shock on TC4 alloy[J]. Inner Mongolia Science Technology Economy, 2010, 222(20):106-108(in Chinese).
[18]	REN X D, ZHANG Y K, ZHOU J Zh, et al. Laser shock processing effects on mechanical properties of Ti6A14V alloy[J]. Functional Materials, 2006, 37(11):1781-1783(in Chinese).

[1]	杨进德 , 周王凡 , 杨涛 , 刘帆帆 , 任旭东 . 多次激光冲击Ti-6Al-4V钛合金表面纳米化研究. 激光技术, 2017, 41(5): 754-758. doi: 10.7510/jgjs.issn.1001-3806.2017.05.027
[2]	杨涛 , 周王凡 , 杨进德 , 侯丽华 , 任旭东 . 激光喷丸对Ti-6Al-4V钛合金中高温性能影响研究. 激光技术, 2017, 41(4): 526-530. doi: 10.7510/jgjs.issn.1001-3806.2017.04.014
[3]	张冲 , 王冠 , 刘赞丰 , 张雅文 . 激光微加工对Ti6Al4V表面形貌及润湿性影响的研究. 激光技术, 2021, 45(1): 31-36. doi: 10.7510/jgjs.issn.1001-3806.2021.01.006
[4]	尹国福 , 鲁建存 , 刘彦义 , 贺爱峰 , 曹椿强 . 激光起爆系统光路完整性检测技术研究. 激光技术, 2011, 35(4): 554-558. doi: 10.3969/j.issn.1001-3806.2011.04.028
[5]	师博飞 , 张安峰 , 齐宝路 , 李涤尘 . 热积累对激光直接成形Ti-6Al-4V组织和性能的影响. 激光技术, 2016, 40(1): 29-32. doi: 10.7510/jgjs.issn.1001-3806.2016.01.007
[6]	高亚丽 , 王存山 , 张梅 , 熊党生 . 镁合金激光表面熔凝技术分析. 激光技术, 2009, 33(4): 362-365. doi: 10.3969/j.issn.1001-3806.2009.04.008
[7]	刘铭坤 , 汤海波 , 方艳丽 , 张述泉 , 刘栋 , 王华明 . 钛合金表面激光熔覆TiC/Ti-Ti2 Co涂层耐磨性. 激光技术, 2011, 35(4): 444-447,452. doi: 10.3969/j.issn.1001-3806.2011.04.003
[8]	武万良 , 黄文荣 , 杨德庄 , 孙荣禄 . Ti-6Al-4V合金基体上激光熔覆Ti+TiC粉末的显微组织. 激光技术, 2003, 27(4): 307-310.
[9]	陈菊芳 , 王江涛 , 周金宇 . 镁合金表面激光熔覆技术的研究进展. 激光技术, 2015, 39(5): 631-636. doi: 10.7510/jgjs.issn.1001-3806.2015.05.010
[10]	游川川 , 肖华强 , 任丽蓉 , 赵欣鑫 . TC4表面激光熔覆Ti-Al-N复合涂层的组织与性能. 激光技术, 2021, 45(5): 585-589. doi: 10.7510/jgjs.issn.1001-3806.2021.05.008
[11]	胡增荣 , 童国权 , 陈长军 , 郭华锋 , 周亮 , 徐家乐 . 激光纳米表面工程技术. 激光技术, 2014, 38(6): 764-770. doi: 10.7510/jgjs.issn.1001-3806.2014.06.009
[12]	王琪琪 , 任乃飞 , 任旭东 . GH4037镍基高温合金激光打孔相变过程数值模拟. 激光技术, 2018, 42(6): 764-768. doi: 10.7510/jgjs.issn.1001-3806.2018.06.007
[13]	陈子豪 , 孙文磊 , 黄勇 , 崔权维 . 镍基高温合金激光熔覆涂层组织及性能研究. 激光技术, 2021, 45(4): 441-447. doi: 10.7510/jgjs.issn.1001-3806.2021.04.006
[14]	张满奎 , 孙桂芳 , 张尉 , 刘卫祥 , 王昆 . 不锈钢表面激光合金化Cr-CrB2层的腐蚀性研究. 激光技术, 2014, 38(2): 240-245. doi: 10.7510/jgjs.issn.1001-3806.2014.02.020
[15]	黄安国 , 汪永阳 , 赵永 , 熊建钢 , 李志远 . 铝合金表面激光熔覆Al+Y粉末的研究. 激光技术, 2009, 33(2): 117-120.
[16]	陈锦堂 , 郭紫莹 , 王成勇 , 谭超林 , 胡映宁 , 刘建业 . 激光选区熔化Ti-6Al-4V在医疗器械领域的研究现状. 激光技术, 2020, 44(3): 288-298. doi: 10.7510/jgjs.issn.1001-3806.2020.03.004
[17]	赵欣鑫 , 肖华强 , 游川川 , 冯进宇 , 肖易 . TC4表面激光熔覆TiAl合金涂层的工艺和组织性能. 激光技术, 2021, 45(6): 697-702. doi: 10.7510/jgjs.issn.1001-3806.2021.06.004
[18]	陈菊芳 , 张永康 , 许仁军 . 镁合金激光表面处理的研究进展. 激光技术, 2008, 32(3): 293-295,311.
[19]	王维夫 , 孙凤久 , 王茂才 . 铝合金表面激光熔覆铜基合金涂层研究. 激光技术, 2008, 32(3): 240-243.
[20]	龚美美 , 谢林圯 , 吴腾 , 师文庆 , 黄江 , 谢玉萍 , 何宽芳 . TC4表面激光熔覆Fe60-TiO₂涂层性能研究. 激光技术, 2022, 46(4): 551-555. doi: 10.7510/jgjs.issn.1001-3806.2022.04.018

点击查看大图

计量

文章访问数: 4665
HTML全文浏览量: 1987
PDF下载量: 470
被引次数: 0

姓名
邮箱
手机号码
标题
留言内容
验证码

留言板

中高温条件下激光冲击处理Ti-6Al-4V表面完整性变化

作者简介: 侯丽华(1988-),女,硕士研究生,现主要从事机械制造及其自动化专业的研究。.

通讯作者: 任旭东, renxd@mail.ujs.edu.cn ;

Change of surface integrity of Ti-6Al-4V titanium alloy by laser shock processing at middle and high temperatures

Corresponding author: REN Xudong, renxd@mail.ujs.edu.cn ;

计量

中高温条件下激光冲击处理Ti-6Al-4V表面完整性变化

通讯作者: 任旭东, renxd@mail.ujs.edu.cn;

作者简介: 侯丽华(1988-),女,硕士研究生,现主要从事机械制造及其自动化专业的研究。

English Abstract

Change of surface integrity of Ti-6Al-4V titanium alloy by laser shock processing at middle and high temperatures

Corresponding author: REN Xudong, renxd@mail.ujs.edu.cn

全文HTML

目录

留言板

中高温条件下激光冲击处理Ti-6Al-4V表面完整性变化

作者简介: 侯丽华(1988-),女,硕士研究生,现主要从事机械制造及其自动化专业的研究。.

通讯作者: 任旭东, renxd@mail.ujs.edu.cn ;

Change of surface integrity of Ti-6Al-4V titanium alloy by laser shock processing at middle and high temperatures

Corresponding author: REN Xudong, renxd@mail.ujs.edu.cn ;

计量

出版历程

中高温条件下激光冲击处理Ti-6Al-4V表面完整性变化

通讯作者: 任旭东, renxd@mail.ujs.edu.cn;

作者简介: 侯丽华(1988-),女,硕士研究生,现主要从事机械制造及其自动化专业的研究。

English Abstract

Change of surface integrity of Ti-6Al-4V titanium alloy by laser shock processing at middle and high temperatures

Corresponding author: REN Xudong, renxd@mail.ujs.edu.cn

全文HTML

目录