填镁改善5052铝合金激光焊接接头机械性能研究

邹宇峰; 金湘中; 何依宁; 张宏圭; 杨洪亮

doi:10.7510/jgjs.issn.1001-3806.2013.06.002

填镁改善5052铝合金激光焊接接头机械性能研究

1.
湖南大学汽车车身先进设计制造国家重点实验室, 长沙 410082;
2.
山东大学材料科学与工程学院, 济南 250061

作者简介: 邹宇峰(1987-),男,硕士研究生,主要从事激光加工焊接方面的工作。.

通讯作者: 金湘中, jin9000xz@hotmail.com ;

基金项目:
国家自然科学基金资助项目(50875079);湖南省自然科学基金资助项目(09JJ3088)
中图分类号: TG456.7

Study on improving mechanical properties of the welds by filling magnesium powder during laser welding 5052 aluminum alloy

1.
The State Key Laboratory of Advanced Design and Manufacturing for Vehicle Body, Hunan University, Changsha 410082, China;
2.
School of Material Science & Engineering, Shandong University, Ji'nan 250061, China

Corresponding author: JIN Xiang-zhong, jin9000xz@hotmail.com ;

CLC number: TG456.7

摘要: 在铝合金激光搭接焊中,镁元素烧损将大大降低焊缝的抗拉强度。为了消除铝合金激光搭接焊中镁元素的烧损对焊接接头的负面影响,采用在铝合金激光焊接接头中填加镁粉的方法,研究焊接速率对镁元素烧损的影响。实验中,测量了焊缝中镁元素在垂直和水平方向的分布,并对焊接接头抗拉强度进行了测试;分析了焊接接头中镁含量和抗拉强度之间的关系,比较了填镁量不同时各焊接接头的抗拉强度。结果表明,镁元素的烧损极大地影响了焊缝的抗拉强度,在激光焊接中填镁能有效地提高焊缝的抗拉强度;相比没填镁,填镁的焊接接头抗拉强度最大改善可以达到36.06%;当焊缝中镁元素的质量分数大约是0.026时,抗拉强度强度达到最大值。这为改善铝合金激光焊接接头强度提供了新的理论依据和方法。
- 激光技术 /
- 抗拉强度 /
- 填镁 /
- 铝合金
Abstract: Magnesium is an important strengthening alloying element in aluminum alloy, the burning loss of which will greatly reduce such mechanical property of the welds as the tensile strength during laser lap welding of aluminum alloy. In order to eliminate the negative effect of the burning loss of magnesium on mechanical property of the welds, filling magnesium powder is adopted filled in laser welding aluminum alloy. The contents of magnesium in the welds were measured both in the vertical and horizontal directions, and the effect of welding velocity on the burning loss of magnesium was experimentally studied. Then, the tensile strength of the welds was tested. Compared after comparing the tensile strength of the welds under different magnesium contents, the relationship between the content of magnesium element of the welds and tensile strength was studied. The results show that the reduction of magnesium content due to the burning loss of magnesium can greatly affect the tensile strength of the welds, filling magnesium during laser welding can effectively improve the tensile strength of the welds, the maximum of the improvement can reach to 36.06% compared to those without filling magnesium. When the mass fraction of the magnesium element in the welds is about 0.026,the tensile strength of the welds reaches the maximum. This study provides new theoretical basis and methods to improve the strength of aluminum alloy laser welded joints.
- laser technique /
- tensile strength /
- filling magnesium /
- aluminum alloy

[1]	EL-BATAHGY A,KUTSUNA M. Laser beam welding of AA5052, AA5083 and AA6061 aluminum alloys[J]. Advances in Materials Science and Engineering,2009,2009: 974182.
[2]	KUO T Y, LIN H C. Effects of pulse level of Nd-YAG laser on tensile properties and formability of laser weldments in automotive aluminum alloys[J]. Materials Science and Engineering,2006, A416(1/2):281-289.
[3]	ZHAO H, DEBROY T. Weld metal composition change during conduction mode laser welding of aluminum alloy 5182[J]. Metallurgical and Materials Transactions,2001, B32(1):163-172.
[4]	MUNDRA K, DEBROY T. Calculation of weld metal composition change in high-power conduction mode carbon dioxide laser-welded stainless steels[J]. Metallurgical and Materials Transactions,1993, B24(1):145-155.
[5]	QI X D, LIU L M. Fusion welding of Fe-added lap joints between AZ31B magnesium alloy and 6061 aluminum alloy by hybrid laser-tungsten inert gas welding technique[J]. Materials and Design,2012,33(4):436-443.
[6]	YU Y Ch, WANG Ch M, YU Sh F, et al. Microstructures and property of butt laser joint of aluminium alloy 5A06 sheets with fiiler[J]. Laser Technology,2010,34(1):34-36(in Chinese).
[7]	BRAUN R. Nd:YAG laser butt welding of AA6013 using silicon and magnesium containing filler powders[J]. Materials Science and Engineering,2006, A426(1/2):250-262.
[8]	XU F, CHEN L, GONG Sh L, et al. Microstructure and mechanical properties of laser welding 5A06 aluminum with filling wire[J]. Applied Laser,2009,29(2):83-86(in Chinese).
[9]	JANDAGHI M, PARVIN P,TORKAMANY M J,et al. Alloying element losses in pulsed Nd:YAG laser welding of stainless steel 316[J]. Journal of Physics,2008,D41(23):235503.
[10]	HE X, DEBROY T. Alloying element vaporization during laser spot welding of stainless steel[J]. Journal of Physics,2003,D36(23): 3079-3088.
[11]	DILTHEY U, GOUMENIOUK A, LOPOTA V, et al. Development of a theory for alloying element losses during laser beam welding[J]. Journal of Physics,2001,D34(1): 81-86.
[12]	JANDAGHI M, PARVIN P, TORKAMANY M J, et al. Measurement of the composition change in Al5754 alloy during long pulsed Nd:YAG laser welding based on LIBS[J]. Applied Physics,2009,42(20): 205301.
[13]	LIANG N, SHENG Y F. Effect of active element-magnesium on the properties of vacuum brazed joints of aluminum alloy[J]. Transactions of the China Welding Institution,2007,28(7):61-64(in Chinese).
[14]	ZHANG Y H, SHI Ch Ch. Research on the role of magnesium in the process of aluminum alloy vacuum brazing[J]. Transactions of the China Welding Institution,1983,4(2):55-69(in Chinese).
[15]	ZHANG H G, JIN X Zh, CHEN G Y, et al. A study on the burning loss of magnesium element in fiber laser welding of aluminum alloy 5052[J]. Laser Technology,2012,36(6):713-718(in Chinese).

[1]	唐海国 , 高明 , 曾晓雁 . 镁合金厚板激光焊缝组织及抗拉强度研究. 激光技术, 2011, 35(2): 152-155. doi: 10.3969/j.issn.1001-3806.2011.02.003
[2]	张宏圭 , 金湘中 , 陈根余 , 张明军 , 邹宇峰 . 光纤激光焊接5052铝合金镁元素烧损研究. 激光技术, 2012, 36(6): 713-718. doi: 10.3969/j.issn.1001-3806.2012.06.001
[3]	骆红 , 胡伦骥 , 黄树槐 , 刘建华 , 胡席远 . 铝合金的激光焊接. 激光技术, 1998, 22(2): 94-98.
[4]	王维夫 , 孙凤久 , 王茂才 . 铝合金表面激光熔覆铜基合金涂层研究. 激光技术, 2008, 32(3): 240-243.
[5]	张继祥 , 刘凤芝 , 高波 , 殷筱依 , 杨泮 . Al-Mg系铝合金脉冲激光焊接性能影响因素分析. 激光技术, 2015, 39(6): 863-868. doi: 10.7510/jgjs.issn.1001-3806.2015.06.028
[6]	余世文 , 周昆 , 张威 , 王维新 , 刘巨峰 , 叶兵 . 6.0mm厚5183铝合金激光摆动焊接工艺研究. 激光技术, 2018, 42(2): 254-258. doi: 10.7510/jgjs.issn.1001-3806.2018.02.022
[7]	赵安安 , 张鸿帅 , 燕国强 , 郭跃文 . 铝合金化铣保护胶激光刻型热应力耦合分析. 激光技术, 2023, 47(3): 419-424. doi: 10.7510/jgjs.issn.1001-3806.2023.03.021
[8]	魏鑫磊 , 李春林 , 薛伟 , 张健 , 朱德华 , 曹宇 . 激光标刻铝合金2维码的手机识读特性研究. 激光技术, 2016, 40(5): 633-637. doi: 10.7510/jgjs.issn.1001-3806.2016.05.004
[9]	李忠 , 刘佳 , 白陈明 , 张亚亮 , 杨玉东 . 超声波对铝合金激光-电弧复合焊接影响的研究. 激光技术, 2019, 43(3): 301-306. doi: 10.7510/jgjs.issn.1001-3806.2019.03.003
[10]	谭兵 , 刘红伟 , 马冰 , 陈东高 , 任宝辉 , 明珠 , 马志华 . 铝合金CO2激光电弧复合焊保护气体影响研究. 激光技术, 2012, 36(4): 497-500. doi: 10.3969/j.issn.1001-806.2012.04.015
[11]	张大文 , 张宏 , 刘佳 , 石岩 . 铝合金连续-脉冲激光焊接工艺对比实验研究. 激光技术, 2012, 36(4): 453-458. doi: 10.3969/j.issn.1001-806.2012.04.006
[12]	王海林 , 黄维玲 , 周卓尤 , 曹红兵 . 铝合金2007的激光焊接. 激光技术, 2003, 27(2): 103-105.
[13]	李忠 , 王涛 , 刘佳 , 石岩 , 白陈明 , 栗红星 . 工艺参量对铝合金复合焊接接头耐蚀性的影响. 激光技术, 2019, 43(2): 189-194. doi: 10.7510/jgjs.issn.1001-3806.2019.02.008
[14]	范勇 , 王声波 , 吴鸿兴 , 郭大浩 , 戴宇生 , 夏小平 . 航空铝合金材料激光冲击强化实验研究. 激光技术, 2003, 27(4): 273-275.
[15]	赵文轸 . 铝合金表面激光处理的三种工艺特点. 激光技术, 1997, 21(2): 87-91.
[16]	金捷 , 张冲 , 张永康 , 朱然 . 激光烧蚀坑阵列微结构对7075-T6粘接强度的影响. 激光技术, 2022, 46(2): 182-187. doi: 10.7510/jgjs.issn.1001-3806.2022.02.006
[17]	范长刚 , 王爱华 , 谢长生 . 铝合金表面激光熔覆的新进展. 激光技术, 1996, 20(6): 366-369.
[18]	李建敏 , 王春明 , 闫飞 , 胡席远 , 吴圣川 , 张威 . 6005A激光-MIG复合焊接头组织及力学性能研究. 激光技术, 2014, 38(6): 733-737. doi: 10.7510/jgjs.issn.1001-3806.2014.06.003
[19]	宋新华 , 金湘中 , 袁江 , 张明军 , 宋斌 , 冯斌华 . 激光深熔钎焊车用铝/钢异种金属试验研究. 激光技术, 2014, 38(3): 342-346. doi: 10.7510/jgjs.issn.1001-3806.2014.03.012
[20]	朱祖昌 , 邱丘 . 铸铝激光熔融处理后的组织与性能. 激光技术, 1996, 20(6): 335-337.

点击查看大图

计量

文章访问数: 3297
HTML全文浏览量: 638
PDF下载量: 619
被引次数: 0

姓名
邮箱
手机号码
标题
留言内容
验证码

留言板

填镁改善5052铝合金激光焊接接头机械性能研究

作者简介: 邹宇峰(1987-),男,硕士研究生,主要从事激光加工焊接方面的工作。.

通讯作者: 金湘中, jin9000xz@hotmail.com ;

Study on improving mechanical properties of the welds by filling magnesium powder during laser welding 5052 aluminum alloy

Corresponding author: JIN Xiang-zhong, jin9000xz@hotmail.com ;

计量

填镁改善5052铝合金激光焊接接头机械性能研究

通讯作者: 金湘中, jin9000xz@hotmail.com;

作者简介: 邹宇峰(1987-),男,硕士研究生,主要从事激光加工焊接方面的工作。

English Abstract

Study on improving mechanical properties of the welds by filling magnesium powder during laser welding 5052 aluminum alloy

Corresponding author: JIN Xiang-zhong, jin9000xz@hotmail.com

全文HTML

目录

留言板

填镁改善5052铝合金激光焊接接头机械性能研究

作者简介: 邹宇峰(1987-),男,硕士研究生,主要从事激光加工焊接方面的工作。.

通讯作者: 金湘中, jin9000xz@hotmail.com ;

Study on improving mechanical properties of the welds by filling magnesium powder during laser welding 5052 aluminum alloy

Corresponding author: JIN Xiang-zhong, jin9000xz@hotmail.com ;

计量

出版历程

填镁改善5052铝合金激光焊接接头机械性能研究

通讯作者: 金湘中, jin9000xz@hotmail.com;

作者简介: 邹宇峰(1987-),男,硕士研究生,主要从事激光加工焊接方面的工作。

English Abstract

Study on improving mechanical properties of the welds by filling magnesium powder during laser welding 5052 aluminum alloy

Corresponding author: JIN Xiang-zhong, jin9000xz@hotmail.com

全文HTML

目录