杂质吸收对光子晶体滤波器设计的影响

刘启能

高级检索

ISSN 1001-3806CN 51-1125/TN 网站地图

留言板

尊敬的读者、作者、审稿人, 关于本刊的投稿、审稿、编辑和出版的任何问题, 您可以本页添加留言。我们将尽快给您答复。谢谢您的支持!

姓名
邮箱
手机号码
标题
留言内容
验证码

杂质吸收对光子晶体滤波器设计的影响

刘启能

文章导航 > 激光技术 > 2008 > 32(3): 327-329,336

引用本文:

Citation:

杂质吸收对光子晶体滤波器设计的影响

刘启能^,

1.
重庆工商大学理学院, 重庆 400067

作者简介: 刘启能(1957- ),男,教授,从事光学与原子分子物理研究.E-mail:ybxyiwc@sina.com.

通讯作者: 刘启能, ybxywic@sina.com

中图分类号: O46

Effect of absorption of dopant on design of photonic crystal filters

LIU Qi-neng^,

1.
Science College, Chongqing Technology and Business University, Chongqing 400067, China

Corresponding author: LIU Qi-neng, ybxywic@sina.com

CLC number: O46

摘要: 为了研究杂质的吸收对光子晶体滤波器设计的影响,引入复折射率并利用特征矩阵法,计算了滤波透射峰的峰值和半峰全宽。滤波透射峰的峰值随杂质的消光系数增加而迅速减小,滤波通道透射峰的半峰全宽随消光系数增加而增大,滤波透射峰的峰值和半峰全宽都随吸收杂质的光学厚度的增加而减小。结果表明,设计光子晶体滤波器时,必须考虑杂质吸收这一重要因素,应选择消光系数小于0.002的掺杂材料,并且杂质的光学厚度应设计在2(λ0/4)左右。
- 材料 /
- 光子晶体 /
- 滤波器 /
- 缺陷模 /
- 消光系数
Abstract: In order to study the effect of dopant absorption on photonic crystal filters,the peak transmissivity and full width at half maxmum(FWHM) of the filters were calculated based on the complex refractive index and the characteristic matrix.It was found that the peak transmissivity decreased with the increment of the extinction coefficient,however the FWHM increased with the increment of the extinction coefficient.Both the peak transmissivity and the FWHM decreased with the increment of the optical thickness of doping.A valuable conclusion is drawn that the absorption of dopant has to be taken into account for the design of a phonic crystal filter and that the extinction coefficient should be less than 0.002 and the optical thickness of doping should be 2(λ0/4) or so.
- materials /
- photonic crystal /
- filter /
- defect mode /
- extinction coefficient

[1]	YABLONOVITCH E Y.Inhibited spontaneous emission in solid-state physics and electronics[J].Phys Rev Lett,1987,58 (20):2059-2061.
[2]	SAJEEV J.Strong localization of photons in certain disordered dielectric superlattices[J].Phys Rev Lett,1987,58 (23):2486-2489.
[3]	LIU Q N.The properties of defect mode and the properties of polarization of in doped one-dimensional photonic crystal[J].Laser Journal,2007,28(1):37-38(in Chinese).
[4]	FU L L,CHEN W Z,ZHENG X L.Modulation of incidence angle to impurity state in photonic crystal[J].Laser Journal,2005,26 (2):22-25(in Chinese).
[5]	FANG Y T,SHEN T G,TAN X L.Study on one dimensional photonic crystal with impurity defect[J].Acta Optica Sinica,2004,24(11):1557-1560(in Chinese).
[6]	ZHOU J G,DUG Q,ZHANG Y W.Electromagnetic modes of thickness-modulated dual-periodic one-dimensional photonic crystals[J].Acta Optica Sinica,2005,54 (8):3703-3707(in Chinese).
[7]	DU G Q,LIU N H.Optical transmission spectra of one-dimensional photoniccrystals with a mirror symmetry[J].Acta Physica Sinica,2004,53(4):1095-1097(in Chinese).
[8]	HUANG H J,OUYANG Z B,XU G W.Investigation of perfect multichannel filtering properties of complex-period photonic crystals[J].Journal of Optoelectronics · Lsser,2003,13(1):50-53(in Chinese).
[9]	MAO H B,YANG C L,LAI Z S.Theoretical study of the tunable optical filter properties based on photonic crystals[J].Acta Physics Sinica,2004,53 (7):2201-2205(in Chinese).
[10]	TIAN G X,WU Y G,WANG Z S.Design and modification of double channel of one-dimensional photonic crystal[J].Acts Optica Sinica,2005,25(5):661-664(in Chinese).
[11]	QIAN X Z.New type of photonic crystal tunable filter[J].Semicondutor Optoelectonics,2005,26(5):382-385(in Chinese).
[12]	HUANG J J,LI G,CHEN M,et al.Simulation dispersion properties of photonic crystal fiber[J].Laser Technology,2006,30(4):432-435(in Chinese).
[13]	XIE Y M,LIU Zh D,WANG H Q.Local defect modesin photonic crystals with negative refractive index structural defects[J].Laser Technology,2006,30 (2):195-198(in Chinese).
[14]	BORN M,WOLF E.Principles of optics[M].7th ed.Beijing:Publishing House of Electronics Industry,2006:615-619(in Chinese).
[15]	BORN M,WOLF E.Principles of optics[M].7th ed.Beijing:Publishing House of Electronics Industry,2006:51-61(in Chinese).

[1]	胡莉 , 张利沙 . 1维掺杂光子晶体宽窄双重滤波器的理论研究. 激光技术, 2010, 34(3): 429-432. doi: 10.3969/j.issn.1001-3806.2010.03.040
[2]	代洪霞 , 刘启能 . 1维方形掺杂光子晶体波导中缺陷模的色散特性. 激光技术, 2013, 37(3): 338-341. doi: 10.7510/jgjs.issn.1001-3806.2013.03.016
[3]	韦吉爵 , 苏安 , 高英俊 , 梁祖彬 , 陈颖川 , 白书琼 . 缺陷对光子晶体透射能带谱的简并效应研究. 激光技术, 2017, 41(1): 56-60. doi: 10.7510/jgjs.issn.1001-3806.2017.01.012
[4]	熊翠秀 , 蒋练军 , 王景艳 . 正负折射率含缺陷1维光子晶体多通道滤波器. 激光技术, 2014, 38(4): 475-479. doi: 10.7510/jgjs.issn.1001-3806.2014.04.009
[5]	刘启能 . 各向异性矩形掺杂光子晶体的缺陷模及量子效应. 激光技术, 2011, 35(4): 499-502. doi: 10.3969/j.issn.1001-3806.2011.04.015
[6]	许江勇 , 苏安 , 周丽萍 , 高英俊 , 谭福奎 , 唐秀福 . 左右手材料光子晶体的双重光学滤波功能. 激光技术, 2018, 42(4): 550-555. doi: 10.7510/jgjs.issn.1001-3806.2018.04.022
[7]	马骥 , 黄正逸 , 沈小明 , 陈宪锋 . 对称双缺陷光子晶体的缺陷模规律. 激光技术, 2010, 34(3): 398-400,404. doi: 10.3969/j.issn.1001-3806.2010.03.032
[8]	王吉科 , 闫珂柱 , 姜迎迎 . 杂质吸收对1维光子晶体孪生缺陷模的影响. 激光技术, 2009, 33(3): 266-268,286.
[9]	金铱 , 黄正逸 , 陈宪锋 , 唐丽 , 是度芳 . 光子晶体缺陷模的偏振特性研究. 激光技术, 2007, 31(3): 277-280.
[10]	王叶荟 , 唐丽 , 倪重文 , 是度芳 . 一维光子晶体非线性微腔的缺陷模和双稳态. 激光技术, 2006, 30(5): 462-464,468.
[11]	刘启能 , 龙涛 , 林睿 , 胡莉 . 平板掺杂光子晶体中电磁波的缺陷模. 激光技术, 2010, 34(3): 363-366. doi: 10.3969/j.issn.1001-3806.2010.03.022
[12]	谢应茂 , 刘正东 , 王慧琴 . 含有负折射率缺陷的光子晶体中的局域缺陷模. 激光技术, 2006, 30(2): 195-197,201.
[13]	高雯婧 , 梁良 . 含增益缺陷层的1维三元光子晶体特性研究. 激光技术, 2013, 37(2): 147-150. doi: 10.7510/jgjs.issn.1001-3806.2013.02.003
[14]	韦应生 , 苏安 , 许江勇 , 唐秀福 , 蒙成举 , 高英俊 . 四元异质结构光子晶体的双通道光学滤波特性. 激光技术, 2018, 42(2): 212-216. doi: 10.7510/jgjs.issn.1001-3806.2018.02.014
[15]	张芬 , 肖峻 , 谢康 . 对称和非对称结构1维光子晶体的滤波特性. 激光技术, 2010, 34(4): 486-488,492. doi: 10.3969/j.issn.1001-3806.2010.04.015
[16]	苑秋红 , 谢康 , 韩艳芬 . 含负折射率材料的1维光子晶体掺杂缺陷模研究. 激光技术, 2010, 34(2): 232-235. doi: 10.3969/j.issn.1001-3806.2010.02.024
[17]	姜迎新 , 方云团 . 纳米金属薄膜同时实现多通道频率和角度滤波. 激光技术, 2010, 34(6): 739-742. doi: 10.3969/j.issn.1001-3806.2010.06.006
[18]	张志新 , 肖峻 . 1维光子晶体的能带结构分析. 激光技术, 2015, 39(4): 525-527. doi: 10.7510/jgjs.issn.1001-3806.2015.04.021
[19]	詹仪 . 木堆结构光子晶体最佳参量的理论分析. 激光技术, 2009, 33(4): 391-392,396. doi: 10.3969/j.issn.1001-3806.2009.04.016
[20]	荣垂才 , 闫珂柱 , 谢应茂 . 二维光子晶体中场的分布. 激光技术, 2008, 32(1): 75-76,79.

点击查看大图

计量

文章访问数: 3993
HTML全文浏览量: 641
PDF下载量: 267
被引次数: 0

杂质吸收对光子晶体滤波器设计的影响

刘启能^,

通讯作者: 刘启能, ybxywic@sina.com

作者简介: 刘启能(1957- ),男,教授,从事光学与原子分子物理研究.E-mail:ybxyiwc@sina.com

1. 重庆工商大学理学院, 重庆 400067

收稿日期: 2007-03-06
录用日期: 2007-03-27
网络出版日期: 2008-06-25

关键词:

摘要: 为了研究杂质的吸收对光子晶体滤波器设计的影响,引入复折射率并利用特征矩阵法,计算了滤波透射峰的峰值和半峰全宽。滤波透射峰的峰值随杂质的消光系数增加而迅速减小,滤波通道透射峰的半峰全宽随消光系数增加而增大,滤波透射峰的峰值和半峰全宽都随吸收杂质的光学厚度的增加而减小。结果表明,设计光子晶体滤波器时,必须考虑杂质吸收这一重要因素,应选择消光系数小于0.002的掺杂材料,并且杂质的光学厚度应设计在2(λ0/4)左右。